(631) 703-8716 
10,000lbs Vehicle Lift Auto Ramp Car Lift 2 Post Lift Auto Hoist 220V
Only .. left! .. people are viewing this, and .. recently purchased it
.. Visitor Right Now
5 Great reasons to buy from us:
SKU#TPLH001
1. Power supply : 220V 60Hz 1Ph
2. Lifting capacity : 10000lbs / 4500kgs
3. Time to full rise : 20-60 sec
4. 1 set truck adapters included
5. Double points safety lock release
6. Intern arm lock system; toe protector with tool tray; top limiter include
Product Description
Safety Mechanism:
•Double Points Safety Lock Release
•Automatic arm lock restraints
•Relief valve built in power pump to prevent overloading
•Door guards protection rubber
•Up-limit switch to protect cylinders working stroke used in safe length scope
•Heavy duty : 9.3mm diameter cable and 118mm pulley reduce high stress on synchronization process and increase cable life
•Stiffened base plate 3mm thickness
•Ultra high molecular self lubricating nylon slider ensures carriage smooth moving up and down
•Anchor bolts/mounting hardware included
Control System:
•Lifting operation by pressing "UP" button on motor
•Manual lowering operation by pressing lever
•Relief valve built in power pump to prevent overloading
•1 set truck adapters included
Before installing your auto lift, check the following:
• Lift Location: Always use architect’s plans when available. Check layout dimension against floor plan requirements making sure adequate space is available. Your lift requires a 220v, 30amp, single phase, grounded electrical source. There should be room enough to operate the lift in a safe manner and without restrictions.
• Overhead Area: The area where the lift will be located should be free of overhead obstructions such as heaters, building supports, electrical lines, doors, lights, etc.
• Floor Area: Visually inspect the site where the lift is to be installed and check for cracked or defective concrete.
Floor Requirements
• A level floor is suggested for proper installation and level lifting. Small differences in floor slopes may be compensated for by proper shimming. If a floor is of questionable slope, consider a survey of the site and/or the possibility of pouring a new level concrete slab.
• New concrete must be adequately cured for at least 30 days.
Concrete Specifications
All models MUST be installed on 3,000 PSI reinforced concrete only. Additional concrete requirements will vary by lift.
DO NOT install auto lift on any asphalt surface or any surface other than concrete.
DO NOT install auto lift on expansion seams or on cracked or defective concrete.
DO NOT install auto lift on a second/elevated floor without first consulting building architect.
DO NOT install auto lift outdoors unless special consideration has been made to protect the power unit from inclement weather conditions.
Product Information
and
SKU#TPLH001
1. Power supply : 220V 60Hz 1Ph
2. Lifting capacity : 10000lbs / 4500kgs
3. Time to full rise : 20-60 sec
4. 1 set truck adapters included
5. Double points safety lock release
6. Intern arm lock system; toe protector with tool tray; top limiter include
Product Description
Safety Mechanism:
•Double Points Safety Lock Release
•Automatic arm lock restraints
•Relief valve built in power pump to prevent overloading
•Door guards protection rubber
•Up-limit switch to protect cylinders working stroke used in safe length scope
•Heavy duty : 9.3mm diameter cable and 118mm pulley reduce high stress on synchronization process and increase cable life
•Stiffened base plate 3mm thickness
•Ultra high molecular self lubricating nylon slider ensures carriage smooth moving up and down
•Anchor bolts/mounting hardware included
Control System:
•Lifting operation by pressing "UP" button on motor
•Manual lowering operation by pressing lever
•Relief valve built in power pump to prevent overloading
•1 set truck adapters included
Before installing your auto lift, check the following:
• Lift Location: Always use architect’s plans when available. Check layout dimension against floor plan requirements making sure adequate space is available. Your lift requires a 220v, 30amp, single phase, grounded electrical source. There should be room enough to operate the lift in a safe manner and without restrictions.
• Overhead Area: The area where the lift will be located should be free of overhead obstructions such as heaters, building supports, electrical lines, doors, lights, etc.
• Floor Area: Visually inspect the site where the lift is to be installed and check for cracked or defective concrete.
Floor Requirements
• A level floor is suggested for proper installation and level lifting. Small differences in floor slopes may be compensated for by proper shimming. If a floor is of questionable slope, consider a survey of the site and/or the possibility of pouring a new level concrete slab.
• New concrete must be adequately cured for at least 30 days.
Concrete Specifications
All models MUST be installed on 3,000 PSI reinforced concrete only. Additional concrete requirements will vary by lift.
DO NOT install auto lift on any asphalt surface or any surface other than concrete.
DO NOT install auto lift on expansion seams or on cracked or defective concrete.
DO NOT install auto lift on a second/elevated floor without first consulting building architect.
DO NOT install auto lift outdoors unless special consideration has been made to protect the power unit from inclement weather conditions.
Product Information
and
.. people are viewing this item
.. visitors have this item in their cart right now
..% of people buy 2 or more
