SKU#HO95EO8LL/OFESH140U

 The concrete floor under this post lift requires for 11 inch thickness.

Model:AA-2PFP45-110V

【Electric 110V/60HZ/1PH/ motor with hydraulic power system】

The HPDMC lift offers exceptional direct-drive lifting performance. This industrial-strength car lift guarantees cutting-edge technology, top of the line materials, a design that’s ahead of its time and a 10,000-lb. Every HPDMC lift offers an abundant roster of options and accessories that allow you to fully tailor the lift to your unique circumstance.

【Symmetric arms design with double lock system】

The highly sophisticated yet simple and dependable HPDMC Series design requires very little service or maintenance for an overall lower cost of ownership.

【Lowered arm tube supports】

Our tube arms have been reconfigured to make it easier to open doors when vehicle lift points are engaged. This is especially useful if your vehicle has low-hanging doors. We take every measure to prevent damage to your property with our two-post lift design.

【Low-profile, dropped-end frame contact pads】

From race cars to lowered compact vehicles, this car lift has the versatility to get under your chassis without damaging your vehicle’s body or frame.

【Lifts come with free set of Truck adapters】

Highly duty oil slider with 10mm steel rope ensures carriage smooth moving up and down. With 8 folded profile column, provide extremely high strengthen working ability.

Specification

Model :AA-2PFP45

Driving Mode: Dual hydraulic cylinders, chain drive
Lock Release :Dual sides manual release
Voltage:220V/60HZ/1PH
Package Dimension:2810*450*850mm
Package Weight:1248lbs

Heavy Duty Design
Thickness of steel for pillar: 5mm

Thickness of steel for arm: 6mm

Thickness of steel for carriage :6mm

Thickness of steel for  basement cover: 3mm

Steel rope diameter: 9.3mm

Steel rope pully diameter: 118mm

Safety Mechanism:
•Double Points Safety Lock Release
•Automatic arm lock restraints
•Relief valve built in power pump to prevent overloading
•Door guards protection rubber
•Up-limit switch to protect cylinders working stroke used in safe length scope
•Heavy duty :9.3mmdiameter cable and 118mm pulley reduce high stress on synchronization process and increase cable life
•Stiffened base plate 3mm  thickness
•Ultra high molecular self lubricating nylon slider ensures carriage smooth moving up and down
•Anchor bolts/mounting hardware included
 

Control System:
•Lifting operation by pressing "UP" button on motor
•Manual lowering operation by pressing lever
•Relief valve built in power pump to prevent overloading
•1 sets truck adapters included

•Lifting Capacity: 10,000 lbs

•Lift Speed: 50 Seconds
•The overall Height  110-1/4"
•The overall Width  139-3/4"

•Arm size: 30-3/4”  -   50-3/8” ( 780-1280mm)    
•Min pad height: 3-3/4"(95mm)
•Lift height max: 70-1/16"(1780mm)
•Drive-thru width clearance: 109-1/4" (2775mm)
•Time to full rise: 20-60 sec

Before installing your auto lift, check the following:
• Lift Location: Always use architect’s plans when available.  Check layout dimension against floor plan requirements making sure adequate space is available.  Your lift
requires a 220v, 30amp, single phase, grounded electrical source.  There should be room enough to operate the lift in a safe manner and without restrictions.
• Overhead Area: The area where the lift will be located should be free of overhead obstructions such as heaters, building supports, electrical lines, doors, lights, etc.
• Floor Area: Visually inspect the site where the lift is to be installed and check for cracked or defective concrete.

Floor Requirements
• A level floor is suggested for proper installation and level lifting.  Small differences in floor slopes may be compensated for by proper shimming.  If a floor is of questionable slope, consider a survey of the site and/or the possibility of pouring a new level concrete slab.
• New concrete must be adequately cured for at least 30 days.

DO NOT install auto lift on any asphalt surface or any surface other than concrete.
DO NOT install auto lift on expansion seams or on cracked or defective concrete.
DO NOT install auto lift on a second/elevated floor without first consulting building architect.
DO NOT install auto lift outdoors unless special consideration has been made to protect the power unit from inclement weather conditions.

Concrete Specifications
All models MUST be installed on 3,000 PSI reinforced concrete only.  Additional concrete requirements will vary by lift.